Overview
A wooden planter is a great way of creating a bed to grow plants and vegetables in if you are short of space. Your wooden planter can be adapted to fit any corner, depending on your needs. And as it's made of pressure-treated timber it can be stained in any colour and won't rot.
Do it:
spring - summer
Takes just:
1 weekend
How to do it
-
Mark and cut all the pieces of timber to the correct lengths, cutting the ends as squarely as possible for a smooth finish. Using a 3mm drill bit, make a hole around 2.5cm from the end of every length to stop the wood splitting when you put in the screws. -
Lay out two 100cm, 60cm and 40cm lengths to form the frame. Butt one end of each length up to the next with the drilled holes on the side. Check the angles with the try square before fitting a screwdriver attachment and fixing the frame together with 7.5cm screws. -
Cut treated gravel board to the appropriate lengths for the planter bottom. Place the bottom boards on the frame. Don't worry if there are gaps up to 5cm wide between the boards as the planter will be lined. Pre-drill the bottom boards, check the frame is square again, then attach the boards to the frame using 5cm screws. -
Flip the frame over onto the other side so the bottom boards sit on the ground. Lay the next course and alternate the corner joins. Check all ends are flush and fix with 7.5cm screws. -
Build up four layers in this way. Instead of a final 60cm piece, lay a 100cm length across the gap to support the raised square. -
For the perfect fit, measure the cross-bar piece when it's in position across the frame and cut it in situ. -
Attach one end of the length with a 7.5cm screw from above, as shown. Fix the other by screwing into it from the outside of the frame. -
Lay the 45cm length across the other gap, lining it up with the adjacent side to make a rectangle (see picture). Check the angles and screw it into place. -
Finish this layer by placing two 40cm lengths at right angles to the 45cm piece, then cut the final length to fit the remaining gap. Continue adding courses of 40cm lengths of timber, with alternating joints, until the raised section of the planter is four layers deep.
"To protect the wood, line the planter inside with plastic, fixing it with small nails. Make drainage holes before filling it with compost."
Comments and rating
Overall rating (from 7 ratings):
5 out of 5
this looks great will definitely try this out!
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
5 out of 5
very impressive ill show it to my husband to see if he will have a go
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
5 out of 5
very nice! might have a bash at that myself!!!
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
How about plans for a garden shed or storage bunker for tools? Many of the ones available commercially are pretty flimsy and expensive for what they are and it would be good to be able to build one to suit my own needs and garden space. David.
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
Great planter - Some plans for a garden/allotment shed would be good - on the lines of unitised walls etc so it is easily adapted in size for various uses. Stu20
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
5 out of 5
I'll have to have a go at this
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
5 out of 5
excellent feature for the corner of the patio
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
5 out of 5
I love how this looks. We are building my daughter and her husband a low level deck soon and we need something to put on the high corner and this looks like it will work just right. I have a question though. Since the plants will be draining directly onto the deck boards do I have to worry about the wood rotting underneath? Of course, the deck is also built with pressure treated lumber.
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.
alecky rated and commented on this article
28 January 2009
4 out of 5
Looks really smart, I'm not a DIY expert but I'd like to have a go at this!
Link to this comment
Report this comment
You are about to report a comment for breaking our Code of Conduct.
Please note, we will not remove a post just because you disagree with what is being said.
This form can only be used for reporting a comment. If you want to contact us please go to our contact us page.