London (change)
Today 23°C / 17°C
Tomorrow 22°C / 14°C

How to make a wooden planter

You will need

  • 5cm x 5cm pressure-treated timber in these lengths: 9 x 100cm, 7 x 60cm, 23 x 40cm, 1 x 45cm
  • 3.45m length of 15cm x 1cm gravel board
  • Saw, drill, 3mm wood drill bit
  • Screwdriver, try square, pencil, tape measure
  • 75 x 7.5cm and 20 x 5cm zinc-plated screws
Do it: spring - autumn
Takes just: one weekend

Overview

A wooden planter is a great way of creating a bed to grow plants and vegetables in if you are short of space. Your wooden planter can be adapted to fit any corner, depending on your needs. And as it's made of pressure-treated timber it can be stained in any colour and won't rot.

How to do it

Drilling holes to make a wooden planter

1Mark and cut all the pieces of timber to the correct lengths, cutting the ends as squarely as possible for a smooth finish. Using a 3mm drill bit, make a hole around 2.5cm from the end of every length to stop the wood splitting when you put in the screws.


Laying out frame

2Lay out two 100cm, 60cm and 40cm lengths to form the frame. Butt one end of each length up to the next with the drilled holes on the side. Check the angles with the try square before fitting a screwdriver attachment and fixing the frame together with 7.5cm screws.


Laying out bottom boards

3Cut treated gravel board to the appropriate lengths for the planter bottom. Place the bottom boards on the frame. Don't worry if there are gaps up to 5cm wide between the boards as the planter will be lined. Pre-drill the bottom boards, check the frame is square again, then attach the boards to the frame using 5cm screws.


Turning over frame

4Flip the frame over onto the other side so the bottom boards sit on the ground. Lay the next course and alternate the corner joins. Check all ends are flush and fix with 7.5cm screws.


Building up layers of wood

5Build up four layers in this way. Instead of a final 60cm piece, lay a 100cm length across the gap to support the raised square.


Measuring cross-bar

6For the perfect fit, measure the cross-bar piece when it's in position across the frame and cut it in situ.


Fixing cross-bar piece

7Attach one end of the length with a 7.5cm screw from above, as shown. Fix the other by screwing into it from the outside of the frame.


Fixing 45cm length piece

8Lay the 45cm length across the other gap, lining it up with the adjacent side to make a rectangle (see picture). Check the angles and screw it into place.


Building raised section of planter

9Finish this layer by placing two 40cm lengths at right angles to the 45cm piece, then cut the final length to fit the remaining gap. Continue adding courses of 40cm lengths of timber, with alternating joints, until the raised section of the planter is four layers deep.


Adam's tip

To protect the wood, line the planter inside with plastic, fixing it with small nails. Make drainage holes before filling it with compost.



Discuss this project

Talkback: How to make a wooden planter
Your comment will appear after a quick registration step

alecky 24/11/2011 at 15:27

Looks really smart, I'm not a DIY expert but I'd like to have a go at this!

sarfush 24/11/2011 at 15:28

this looks great will definitely try this out!

weejen 24/11/2011 at 15:28

very impressive ill show it to my husband to see if he will have a go

myself 24/11/2011 at 15:28

very nice! might have a bash at that myself!!!

Stu20 24/11/2011 at 15:28

Great planter - Some plans for a garden/allotment shed would be good - on the lines of unitised walls etc so it is easily adapted in size for various uses. Stu20

See more comments...